{"title":"Best Seller","description":"","products":[{"product_id":"rpm-front-suspension-arm-set-for-hpi-baja-5b-5t-5sc","title":"RPM RC Products: Front A-arms for 5B - Black","description":"\u003cp\u003eRPM front A-arms for the HPI Baja 5SC, 5T \u0026amp; 5B are designed around the stock A-arm geometry, no additional parts or accessories are needed. We’ve eliminated most of the hard rib angles in favor of smoothly contoured curves that enhance survivability during extreme impacts. Both the upper and lower A-arms incorporate much larger and stronger corner webs than the stock A-arms while RPM lower A-arms have a redesigned center brace structure that helps the rigidity and strength considerably by spreading impact energies over a much larger area. RPM A-arms will hold their shape better and have less flex than the stock arms as well!\u003cbr\u003e\u003cbr\u003eAfter extensive in-house review of 5SC, 5T \u0026amp; 5B A-arms in stock form and listening to Baja owners, we found that the stock pivot ball socket tends to break out under certain impact conditions. We addressed this problem by adding nearly 15% more material around the diameter of the pivot ball socket and we redesigned the shape of the socket to add more support and improve crash survivability without creating any interference with suspension or steering movement. While we were redesigning the pivot ball area, we reduced the amount of slop in the ball socket to help improve and maintain more consistent camber and toe angles for smoother, more precise steering.\u003cbr\u003e\u003cbr\u003eAnother problem we encountered with the stock A-arms is the lack of protection for the very low-hanging front shocks. We solved that problem in a couple of ways. First, we elongated the lower shock mount, leaving no part of the shock exposed. Next, we incorporated a unique lower A-arm skid plate that completely covers \u0026amp; protects the lower shock mount. This skid plate adds serious bulletproof RPM protection to the lower end of those extremely expensive shocks while adding strength and support to the whole lower A-arm. Additionally, these skid plates are reversible! Since the A-arm is angled up, only the lowest part of the skid plate (the rear area) will see the most wear. By making the skid plates reversible, Baja owners run the skid plates until they wear thin on the one end, swap them from one side to the other and they’re good to go for more punishment!\u003cbr\u003e\u003cem\u003e\u003cstrong\u003e\u003cbr\u003eTech Notes: \u003c\/strong\u003e\u003c\/em\u003e RPM A-arms are sold in sets consisting of one upper A-arm, one lower A-arm, one lower a-arm skid plate, two shock spacers and two skid plate mounting screws.\u003c\/p\u003e\n\u003ch2\u003e\u003cem\u003e\u003cstrong\u003eTwo kits will be needed to complete one vehicle.\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h2\u003e","brand":"RPM RC Products","offers":[{"title":"Default Title","offer_id":21048538398797,"sku":"RPM-82142","price":47.5,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/RP82142_RPM_5B_FrontArmSet_Black_web.jpg?v=1547108147"},{"product_id":"ngk-cmr7h-spark-plug","title":"NGK CMR7H Spark Plug","description":"\u003cmeta charset=\"utf-8\"\u003e\n\u003cp\u003e\u003cstrong\u003eNGK CMR7H spark plug\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e10mm thread, 1\/2\" reach, 5\/8\" hex, gasket seat, resistor plug. Also fits billet head kits for scooters and pocketbikes. \u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eZenoah part # 3699-91867\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eHPI Part # 15454 or 3066\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eFG part # 07343\/08\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eStock part on:\u003c\/strong\u003e\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eZenoah G230RC G260RC G240RC G270RC G290RC G320RC Motors Zenoah 231and 260 PUH and PUM Motors\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan be used on:\u003cbr\u003e\u003c\/strong\u003e\u003cspan\u003eCY23, CY26, CY27, CY29, GP290\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eGP460, or any other R\/C style motor with same thread size on cylinder for plug.\u003c\/span\u003e\u003c\/p\u003e","brand":"NGK","offers":[{"title":"Default Title","offer_id":12448878133325,"sku":"NGK-EE132","price":9.99,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/CMR7H_Spark_Plug.jpg?v=1531206317"},{"product_id":"kraken-rc-v3-hd-chrome-steel-hinge-pins-for-hpi-baja-5b-5t-5sc","title":"Kraken RC: V3 HD Chrome Steel Hinge Pins for HPI Baja 5B\/5T\/5SC","description":"\u003cmeta charset=\"utf-8\"\u003e\n\u003cp\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003cstrong\u003eKraken RC V3 HD Chrome Steel Hinge Pins for HPI Baja\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eNewly updated V3 HD is now stronger than ever! These Steel Hinge Pins have been specially heat treated for maximum toughness and durability. The Chrome coating ensures maximum lubricity for all your suspension travels. Installation is fast and easy with our clip less design. A little use of blue loctite is highly recommended for the set screws.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures:\u003cbr\u003e\u003c\/strong\u003e- Heat Treated for maximum strength \u003cbr\u003e- Clipless Design\u003cbr\u003e- Chrome coated for maximum lubricity\u003c\/p\u003e","brand":"Kraken RC","offers":[{"title":"Default Title","offer_id":12448878166093,"sku":"KRA-TR893","price":99.99,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/TR893_Kraken_V3hinge_pins-hpi-baja.jpg?v=1531206318"},{"product_id":"one-seven-rc-pull-start-assembly","title":"Rovan Sports: Pull Start Assembly","description":"\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eBlack starter assembly for Zenoah \u0026amp; CY Motors\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eChung Yang part# 322-233000\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eSame as HPI part # 15478\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThis is a complete starter - Comes as pictured with inner reel, cord, pawl, etc. (includes 4 mounting bolts, M4x16)\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eStock part on the \u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eCY23  CY26  CY27  CY29  GP290\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eGPL290, F270, CY23HR CY29 Headkit engines\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eCan be interchanged with the Zenoah RC starter assembly for use on Zenoah G230RC G260RC G240RC G270RC G290RC G320RC\u003c\/span\u003e","brand":"Rovan Sports","offers":[{"title":"Default Title","offer_id":12448879804493,"sku":"ROV-67024","price":20.0,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/67024_Black_Pull_Start.jpg?v=1531206333"},{"product_id":"walbro-wt-990-high-performance-carburetor-for-zenoah-cy-engines","title":"Walbro: WT-990 High-Performance Carburetor for Zenoah \/ CY Engines","description":"\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eWalbro WT-990 high-performance carburetor. This is the carburetor recommended by Zenoah for upgrading your RC-style engine. Engines with the standard carburetor (WT-603, WT-668, etc) tend to experience a lag in low-end acceleration when tuned for peak power. Carburetor specs: Walbro WT-990. 15.88mm bore, 12.7mm venturi, independent tunable high and low speed jets. \u003c\/span\u003e\u003cb\u003eThis carburator does not have an internal choke.\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eNote: This carburetor now comes standard with modified throttle shaft, so it will work perfectly in most R\/C applications such as HPI Baja, FG Modellsport, etc. As this is a high performance carb this does not have a built in choke.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe WT-990 Carburetor is the same as the WT-813 WITHOUT an internal acceleration pump.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eZenoah part# 575655001\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eFg part # 07855\u003c\/span\u003e","brand":"Walbro","offers":[{"title":"Default Title","offer_id":12959233966157,"sku":"WAL-av990","price":149.0,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/Walbro_990.jpeg?v=1539218186"},{"product_id":"rpm-rc-products-rear-a-arms-for-5b-black","title":"RPM RC Products: Rear A-arms for 5B - Black","description":"\u003cp\u003eTwo months prior to the release of these rear A-arms for the HPI Baja 5B \u0026amp; 5T, we released our version of the front A-arms. In that short amount of time, the durability of our Baja A-arms displayed their unbeatable nature! That kind of performance can now be matched out back with our rear A-arms for the 5SC, 5B \u0026amp; 5T.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRPM\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eBaja rear A-arms start with the basic geometry of the stock arms so they are direct replacement parts – no additional parts will be needed. However, we’ve made a number of modifications to the arms to improve performance and durability. Key durability features are as follows:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe shock mount on the lower A-arm has been moved forward by a full 1\/4” to help reduce the severe rubbing issue of the wheel at the shock mount that would cause stock arms to break.\u003c\/li\u003e\n\u003cli\u003eBy moving the shock mount forward, we were able to increase the material around the shock mount to protect the lower shock rod end, preventing it from being the lowest hanging component of the A-arm assembly.\u003c\/li\u003e\n\u003cli\u003eWe’ve incorporated a third inner hinge pin boss at the inside hinge pin of the lower A-arm and tied in structural ribs that help disperse impact energy and rotational forces from engine torque over all three hinge pin bosses.\u003c\/li\u003e\n\u003cli\u003eSimilar corner webs to those found on our front A-arms have been designed into the rear upper and lower A-arms to help improve strength and durability.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIn the performance department, we moved the rear hub carrier forward by 1\/8” over stock geometry. While this does little to change the overall wheelbase of the vehicle, what it does do is alter the angle of the drive shaft as it exits the differential. This reduces the tendency of the Baja to squat under acceleration. By sliding the rear hub carrier forward, we use the torque of the motor to effectively “push” the rear wheels into the ground, using both the weight of the Baja and the torque of the motor to improve acceleration performance. Up top,\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eRPM\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003erear upper A-arms have had a shape change for added lateral stability – the stock “Y” shape tends to allow the upper pivot ball to move forward and backward while the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eRPM\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e“D” shape holds the upper pivot ball in place more solidly, providing a more consistent feel to the performance of the Baja.\u003c\/p\u003e\n\u003cp\u003eWe mold our Baja 5SC, 5B \u0026amp; 5T rear A-arms in both a stealthy black and a dyeable white version for those that like to personalize their vehicles. A little Rit clothing dye, some hot water and our dyeable A-arms can be dyed to any color you prefer!\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003e\u003cspan\u003eTech Notes:\u003c\/span\u003e\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eRPM\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eRear A-arms for the Baja 5SC, 5B \u0026amp; 5T are sold in sets consisting of one upper and one lower A-arm. Two sets will be needed to complete one vehicle.\u003c\/p\u003e","brand":"RPM RC Products","offers":[{"title":"Default Title","offer_id":21048598265933,"sku":"RPM-82252","price":45.0,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/5B_Rear_A_arm_-_black.jpg?v=1547111098"},{"product_id":"aka-premium-tire-glue-0-7oz","title":"AKA: Premium Tire Glue - 0.7oz","description":"\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eAKA Premium Tire Glue - 0.7oz\u003c\/span\u003e","brand":"AKA","offers":[{"title":"Default Title","offer_id":21170685673549,"sku":"AKA-38001","price":17.5,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/38001-800x800.jpg?v=1549861512"},{"product_id":"orca-oe1-esc-black-1-10-scale-competition-esc","title":"ORCA: OE1 ESC Black 1\/10 Scale Competition ESC","description":"\u003cmeta charset=\"utf-8\"\u003e\n\u003cp\u003eIntroducing the ORCA OE1 Competition ESC!\u003c\/p\u003e\n\u003cp\u003eThe new ORCA OE1 features all new hardware and firmware.  \u003c\/p\u003e\n\u003cp\u003eWith feedback from top drivers across all disciplines of competition - ORCA has enhanced the electronic speed control to deliver the OE1!\u003c\/p\u003e\n\u003cp\u003eSPECIFICATIONS :\u003cbr\u003e– Brushless System\u003cbr\u003e– Multiple Adjustable Parameters use optional program card\u003cbr\u003e– BEC : 5A 6V \/ 7.2V\u003c\/p\u003e\n\u003cp\u003e– Peak Current 760A\u003c\/p\u003e\n\u003cp\u003e– Motor limited over 4.5T\u003cbr\u003e– Motor Type : Brushless sensored 540 size Motor\u003cbr\u003e– Voltage input : DC 4.8V – 9.9V\u003cbr\u003e– 2cells LiPo \/ 2-3cells LiFe\u003cbr\u003e– Dimensions : 33.3(L) x 41(W) x 20.8(H) mm\u003cbr\u003e– Weight : 43g excluded wires\u003c\/p\u003e","brand":"ORCA","offers":[{"title":"Default Title","offer_id":21170796396621,"sku":"ES18OE12-4S","price":299.99,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/Oe1esc_4-800x800.png?v=1626063915"},{"product_id":"xray-differential-gasket-304990","title":"XRAY: DIFF GASKET (4)","description":"\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eThis is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1\/10 touring cars equipped with the Light Weight Gear Differential (\u003c\/span\u003eXRA304900\u003cspan\u003e).\u003c\/span\u003e","brand":"XRAY","offers":[{"title":"Default Title","offer_id":28120094310477,"sku":"XRA-304990","price":12.5,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/304990_1.jpg?v=1670274804"},{"product_id":"xray-composite-front-susp-arm-1-hole-hard","title":"XRAY: FRONT SUSPENSION ARM - HARD - 1-HOLE","description":"\u003cp\u003eMolded composite front lower suspension arm made from hard material. 2mm longer to better fit new suspension mounts. Fits T4’14. \u003cbr\u003e\u003cbr\u003eAfter extensive testing of many different composite mixtures, the factory team identified this new blend as the optimum choice for mass production. The new hard suspension arm is specifically designed to be used in extremely hot conditions to reduce flex and deformation; however due to reduced flex, the arms are less resistant to extreme impacts.\u003cbr\u003e\u003cbr\u003eRedesigned to allow mounting of optional # 302190 graphite plate, the new arms include 4 reinforced holes.\u003c\/p\u003e\n\u003cp\u003eProduct released: 11th September 2013\u003c\/p\u003e","brand":"XRAY","offers":[{"title":"Default Title","offer_id":28128042975309,"sku":"XRA-302168","price":12.5,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/files\/302168.jpg?v=1701889847"},{"product_id":"xray-composite-c-hub-left-4-deg-medium","title":"XRAY: COMPOSITE C-HUB LEFT - 4° DEG. - MEDIUM (ECS)","description":"\u003cmeta charset=\"utf-8\"\u003e\n\u003cp\u003eMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-side C-hub #302364. Can be also used for foam tires.\u003cbr\u003e\u003cbr\u003eNew C-hub has large openings for quicker \u0026amp; easier assembly\/disassembly of CVDs. The entire CVD assembly can be easily inserted\/removed through the C-hub without the need for disassembly, and the large openings prevent binding of the CVD in serious crashes.\u003cbr\u003e\u003cbr\u003eThe C-hubs are available in all standard caster angles (0°, 2°, 4° and 6°) and are also available in 4 different hardnesses (Medium, Hard, Graphite and Alu) that are optimized for particular racing conditions. The EU Edition includes medium rigidity (M) C-hubs specially optimized for rubber-tire racing, while the US Edition includes hard rigidity (H) C-hubs specially optimized for foam-tire racing.\u003c\/p\u003e\n\u003cp\u003eProduct released: 28th November 2007\u003c\/p\u003e","brand":"XRAY","offers":[{"title":"Default Title","offer_id":28128170967117,"sku":"XRA-302364","price":11.5,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/files\/302364_1.jpg?v=1686701467"},{"product_id":"xray-ball-joint-4-9mm-open-v2-8","title":"XRAY: COMPOSITE BALL JOINT 4.9MM - OPEN - V2 (8)","description":"\u003cmeta charset=\"utf-8\"\u003e\n\u003cp\u003eMolded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3, T4, RX8, XB8, NT1, X1 and GTX8\u003c\/p\u003e","brand":"XRAY","offers":[{"title":"Default Title","offer_id":28128502382669,"sku":"XRA-302663-V2","price":15.5,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/files\/302663.jpg?v=1701889342"},{"product_id":"gens-ace-5500mah-7-6v-100c-2s-hardcase-lipo-4mm-plug","title":"Gens Ace: 5500mAh 7.6V 100C 2S Hardcase Lipo - 4mm Plug","description":"\u003cmeta charset=\"utf-8\"\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cmeta charset=\"utf-8\"\u003e\n\u003cp\u003e\u003cstrong\u003eGens ace 5500mAh 7.6V High Voltage 100C 2S2P HardCase Lipo Battery 29# \u003c\/strong\u003efits for both 1:10 off road stock and modified class. Also, they fit 1:10 Formula model and 1:10 Professional Drifting model EFRA \u0026amp; BRCA legal. \u003cspan\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\n\u003cstrong\u003eGens ace 5500mAh 7.6V 100C 2S2P HardCase Lipo Battery \u003c\/strong\u003eSpecs:\u003c\/h3\u003e\n\u003cp\u003e- Capacity: 5500mAh\u003cbr\u003e- Voltage: 2S\/7.6V\u003cbr\u003e- Discharge Rate: 100C\u003cbr\u003e- Weight: 209g\u003cbr\u003e- Size: 96*47*25mm\u003c\/p\u003e","brand":"Gens Ace","offers":[{"title":"Default Title","offer_id":28544728891469,"sku":"GA-5500-2S100-S-HV-RS","price":129.95,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/GA5500-2S100-S-HV-800x800.jpg?v=1561431675"},{"product_id":"orca-oe1-world-edition-esc-160a-2s-ultra-low-resistance","title":"ORCA: OE1 World Edition ESC 160A 2S Ultra Low Resistance","description":"\u003cmeta charset=\"utf-8\"\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eWill add more details as they come to hand......\u003c\/span\u003e\u003c\/p\u003e","brand":"ORCA","offers":[{"title":"Default Title","offer_id":43777831960821,"sku":"ES22OE1_WLE","price":360.0,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0012\/9043\/6685\/products\/ES22OE1_WLE-800x800.jpg?v=1679986414"}],"url":"https:\/\/one7rc.co.nz\/collections\/best-seller.oembed","provider":"One 7 RC","version":"1.0","type":"link"}