
XRAY: SPUR GEAR "H" 84T / 48 - ORANGE
XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsMolded composite servo saver set - extra stiff. Consists of 4 springs to make the servo saver strong enough to prevent extreme steering deflection ...
View full detailsLow-friction 3.5mm drive pin clips for protecting and cushioning drive shaft pin in diff outdrives. Made from all-new, extra-strong composite mixt...
View full detailsOptional specially-modified high-performance Kevlar®-reinforced 351mm-long, 3mm-wide drive belt.This belt is very thin and elastic as possible for...
View full detailsMolded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3, T4, RX8, XB8, NT1, X1 and GTX8
New X4 Alu Hub - Swiss 7075 T6• Alu hubs for X4• Ultra-strong• Long life• Reduces flex• Improves consistency• Full height adjustability• Mainly for...
View full detailsThe unique CFF suspension arms are an elegant engineering achievement that look great and perform even better on the track. Using XRAY's own newly ...
View full detailsThis is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsOptional specially-modified high-performance Kevlar®-reinforced 513mm-long, 3mm-wide front drive belt.This belt is very thin and elastic as possib...
View full detailsOptional specially-modified high-performance Kevlar®-reinforced 189mm-long, 3mm-wide rear drive belt.This belt is very thin and elastic as possible...
View full detailsThreaded 4.9mm ball end with 8mm thread length for connection to molded ball joints. Set of 2.
Molded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsEccentric bushings for adjusting suspension settings, made from tough composite. Fits XB4 alu suspension holders. Using eccentric suspension bushi...
View full detailsXRAY precision molded offset spur gear 81 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass.
The unique CFF suspension arms are an elegant engineering achievement that look great and perform even better on the track. Using XRAY's own newly ...
View full detailsPrecision-molded Graphite composite hub for X4 features new suspension geometry for improved steering and traction. The hubs contain updated drive ...
View full details78-tooth large external spur gear for center differential. Molded from specially-formulated tough composite material. Tooth number stamped for easy...
View full detailsOptional spur gear for 3-Pad Slipper Clutch. Precision-molded slipper clutch spur gear 75T 48P is made from XRAY's exclusive secret blend of compos...
View full detailsXRAY rear spring set for NT1. Different spring tensions to fine tune your car. Powder-coated for easy identification. Developed from extensive test...
View full detailsSuspension pivot pins, hardened for very high durability and long life, polished for smooth operation. Used on inboard pivot point of XB4 suspensio...
View full detailsPrecision-machined bushing for front C-hub steering block pivot screws on XRAY T2, T3. Includes 4 pieces: 2 short + 2 long.
Molded composite 4.9mm ball joints, special design for X4 front and rear upper arms. For connection to 4.9mm ball. The front composite ball joints ...
View full details