
XRAY: SPUR GEAR "H" 84T / 48 - ORANGE
XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsMolded composite steering block of “hard” hardness (H) for foam-tire racing. The steering block features two Ackermann positions, and uses small b...
View full detailsLow-friction 3.5mm drive pin clips for protecting and cushioning drive shaft pin in diff outdrives. Made from all-new, extra-strong composite mixt...
View full detailsMolded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3, T4, RX8, XB8, NT1, X1 and GT...
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsThreaded 4.9mm ball end with 8mm thread length for connection to molded ball joints. Set of 2.
This is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsComplete gear differential set for XRAY T3 includes composite differential case and cover with pulley. Differential gears are made from tough compo...
View full detailsPrecision-molded 20T layshaft pulleys for XRAY T2’008, T2'009 and T3 includes composite shims. Standard pulleys for XRAY T2’008, T2'009, T3 US Foa...
View full detailsPrecision-molded 20T layshaft pulley made of specially-formulated graphite composite material that is a perfect balance of reliability and perform...
View full detailsThreaded 4.9mm ball end with 5mm thread length for connection to molded ball joints. Set of 2.
Alu shims 3x6mm size, 1mm thick, set of 10. Available in Black, Orange or Silver
Molded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crash...
View full detailsPolished chrome pin for ECS drive shaft, 2.0 x 9.0mm. Specially hand-ground for maximum precision. To help prevent of loosening of the setscrew fr...
View full detailsSpecially-modified high-performance 189mm-long and 3mm-wide rear drive belt comes standard in XRAY T2’009 Rubber-Spec Conversion Set – 38T Pulley.T...
View full detailsThreaded 4.9mm ball end with 10mm thread length for connection to molded ball joints. Set of 2.
Molded composite 4.9mm ball joints, special construction. For connection to 4.9mm ball. Set of four. Fits XRAY T2, T3.
Rubber O-ring fits over 5mm shaft. 1mm thick. Set of 10 pieces.
Polished chrome pin for ECS drive shaft, 2.0 x 9.0mm. Specially hand-ground for maximum precision. To help prevent of loosening of the setscrew fr...
View full detailsXRAY precision molded offset spur gear 81 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass.
Alu shims 3x6mm size, 4mm thick, set of 10. Available in Black & Silver
Set of two adjustable steering rod turnbuckles, manufactured from world-renowned top-secret "Hudy Spring Steel". Product released: 4th July 2002
Alu shims 3x6mm size, 2mm thick, set of 10. Available in Black, Orange and Silver